Buy Cheap RotoZip DC1 Duracut Bit Pack From Here Now!
Cuts cement type boards, plaster, lath and stucco. For use with RotoZip spiral saws (item#s 150692, 150693, 150694 and 150695) unless otherwise noted. U.S.A.
Readmore
Technical Details
- RotoZip Duracut bit pack- Ideal for use on cement board, stucco, and plaster
- For long, fast, lateral, and irregular cuts
- Use with RotoZip, RotoMite, and SpiraCut power tools
- 4-by-2-by-.1-inches at 1-ounce
See more technical details
By Timothy D. Ulmen (Seattle WA)
I used this to cut a hole in lath and plaster. It made enough holes for about 6-8 normal electrical boxes. Unfortunately the bit was pretty much toast after that. It did a good job but by the end it was almost burning the edges of the lath. Not that durable but good enough.
By P. Ho (New England)
I called this the wood eraser. I ran this against the edge of the wall to remove excess plywood, and it was a breeze. I couldn't do that with a jigsaw because it was right against wall in the corner.
I also had to cut a circle for a hood vent. The original was rectangular. Trace the area to cut, and got it done in about 15 min. Couldn't think of any other tool that can do it easier. Will buy another for backup.
It does kick back a little, but you get used to it and use a little more strength to stabilize it.
By M. Larimore (Coconut Grove, Florida United States)
I used this to route a trough up my wall to conceal speak wire to my home theater speakers. It worked like a charm!!! My house is 1955 with plaster/mortar walls. I also used the dust extractor adapter - What a charm ABSOLUTELY NO DUST!!! If you have a Rotozip and a dust problem you need the dust extractor!!!
By David A. Cohen (Poughkeepsie, NY)
I bought this bit at home depot for $8 and used it to cut 4 sheets of hardebacker board into a circle for an outdoor mosaic table substrate, using a 3 1/4 hp router and trammel arm. The bit worked quite well, athough I noticed I had to get the RPMs up on the variable speed router to get it to cut easily. I doubt using this bit in a lower powered roto zip could've produced the same results.
Perhaps the folks who don't like this bit should retry it in a router.
By Victor H. Agresti (Gaithersburg, MD United States)
RotoZip DC1 Duracut Bit
Pros:
- 1/4" bits have significantly greater resistance to breaking than 1/8" bits. It's still possible to snap one, but you have to use much more force. If you are frustrated with how easy it is to snap 1/8" bits, and your application will be OK with a 1/4" bit, try one of these. (Of course, the tool will need a 1/4" collet.)
- Carbide cutters last much longer than tool steel.
- Works quite well on soft materials, such as most wood, plastics, and drywall. Has an excellent life if used only on softer materials. They work best at very high speed. I.e., instead of a drill, try them in a router or high-speed rotary cutter.
Cons:
- As with any such bit, when the material gets harder, it becomes less effective -- to useless. E.g., using it on hard products will dull the bit in a hurry. E.g., porcelain or other hard tiles, concrete products such as blocks, bricks, concrete stucco (in spite of their sales pitch), glass, steel, etc. They work pretty well on some tile backer-boards, but this wears them out faster.
Other:
Cutting some materials, such as drywall, creates lots of dust. I use a respirator.
Images Product
Buy RotoZip DC1 Duracut Bit Pack Now
Buy RotoZip DC1 Duracut Bit Pack |
Cheap RotoZip DC1 Duracut Bit Pack | Low Price RotoZip DC1 Duracut Bit Pack | Best RotoZip DC1 Duracut Bit Pack | Order RotoZip DC1 Duracut Bit Pack | Good RotoZip DC1 Duracut Bit Pack | Lowest RotoZip DC1 Duracut Bit Pack | Save RotoZip DC1 Duracut Bit Pack | Discount RotoZip DC1 Duracut Bit Pack | Purchase RotoZip DC1 Duracut Bit Pack | Shop RotoZip DC1 Duracut Bit Pack | Buying RotoZip DC1 Duracut Bit Pack | Where RotoZip DC1 Duracut Bit Pack
0 comments:
Post a Comment